Introduction
The part number 170180-01-00 is a Vibration Transmitter designed to monitor the overall vibration (typically velocity) of industrial machinery. This type of device is a loop-powered, two-wire sensor that integrates a piezoelectric sensing element with built-in signal conditioning electronics. It converts mechanical vibration directly into a standardized 4-20 mA analog output signal, which is proportional to the vibration level. This design allows for simple installation, long-distance signal transmission to PLCs or DCS, and is a fundamental component for basic machinery condition monitoring and predictive maintenance programs.
Technical Parameters
The following table outlines the typical technical specifications for the 170180-01-00 Vibration Transmitter.
| Parameter Category | Specification |
|---|---|
| Part Number | 170180-01-00 |
| Description | 4-20 mA Two-Wire Vibration Velocity Transmitter |
| Physical Dimensions (Body) | Approximately 80 mm (3.15 in) in height 35 mm (1.38 in) in diameter (Excluding mounting thread) |
| Weight | Approximately 0.4 kg (0.88 lbs) |
| Measurement Type | Velocity (Peak or RMS) |
| Frequency Range | 10 Hz to 1000 Hz (600 to 60,000 CPM) |
| Output Signal | Two-Wire 4-20 mA |
| Measurement Range | Scalable, typically a range like 0-25 mm/s (0-1.0 in/s) peak or equivalent. |
| Power Supply | 12 to 30 VDC (Loop Powered) |
| Mounting | 1/4-28 UNF or M10 threaded stud on the base |
| Electrical Connection | Integral cable with flying leads or a 2-pin connector |
| Housing Material | Stainless Steel |
| Operating Temperature | -40°C to +85°C (-40°F to +185°F) |
Note: These specifications are representative of this model and class of transmitter. The exact output scaling and connector type are defined by the part number suffix. Always consult the official manufacturer's datasheet for precise specifications.
Application Scenarios
This vibration transmitter is widely used for general-purpose machinery condition monitoring on a variety of rotating equipment where a simple, reliable, and continuous vibration signal is required.
Motor Condition Monitoring:
Mounted on the bearing housings of critical AC and DC motors in manufacturing plants, HVAC systems, and water treatment facilities to provide a continuous health indicator and detect issues like bearing wear and imbalance.
Pump Vibration Monitoring:
Installed on centrifugal and positive displacement pumps to monitor overall vibration levels. The 4-20 mA signal can be wired directly to the plant's control system to trigger alarms for conditions like cavitation or mechanical looseness.
Fans and Blowers:
Used on industrial fans, such as cooling tower fans or boiler draft fans, to monitor bearing condition and detect imbalance, helping to prevent failures that lead to unplanned downtime.
Compressors:
Applied to the casing of rotary screw and reciprocating compressors to track overall vibration health and provide an early warning of developing mechanical faults.
General Rotating Machinery:
An ideal solution for non-critical or auxiliary equipment (e.g., conveyors, mixers) where a full machinery protection system is not justified, but basic vibration tracking is desired for a cost-effective predictive maintenance strategy.
Global direct procurement guarantee
All products are purchased directly from overseas original manufacturers or authorized channels, 100% guaranteed genuine quality, sufficient spot inventory, and comprehensive model coverage
Quality Commitment
Each product has been tested by our technicians, providing 12-month long warranty, worry-free after-sales
Flexible procurement plan
- Bulk order enjoys Friendship discount (2 pieces or more can be applied)
- Long-term cooperative customers can apply for priority supply
Full service support
7×24 hours technical consultation, from selection guidance to installation and commissioning to provide full life cycle service (paid)
Why do so many customers choose us?
On the basis of the same quality, we provide:
- More competitive price system
- Faster logistics response
- More complete technical support (free product technical documentation)
Your trust is the driving force for our continuous progress, submit your requirements immediately to get exclusive quotes
