Product No.: 330180-X1-00 149032-08 - General Introduction
This product is a highly specialized, pre-configured vibration transducer assembly or complete sensor kit for critical machinery monitoring. The complex part number indicates it is not a standard off-the-shelf item but a system-engineered solution with specific performance characteristics and installation features.
330180: This is the base product family, typically associated with seismic velocity transducers (e.g., 4.5 Hz or 14.4 Hz natural frequency) or industrial accelerometers for measuring casing/bearing cap vibration.
-X1-00: The "X1" denotes a special variant or custom configuration. This could specify a unique sensitivity (e.g., 500 mV/in/s), a specific mounting thread (e.g., ¼-28 UNF), an integral cable with a special jacket, or an extended temperature range. "-00" suggests it's the base variant of this special configuration.
149032-08: This is the assembly or kit part number. The "-08" suffix often indicates a complete field-mounting kit, which includes not just the transducer itself, but also necessary accessories such as a mounting stud, lock washer, cable gland, connector, and sometimes even a handheld carrying case.
This assembly is designed for reliable, long-term installation in harsh environments to measure absolute (casing) vibration on turbines, pumps, fans, and other large rotating equipment.
Detailed Parameters
| Parameter Category | Specification | Details / Notes |
|---|---|---|
| Transducer Type | Piezoelectric Velocity Sensor (Most Probable) or Low-Frequency Accelerometer. | Designed to measure vibration velocity (in/s or mm/s RMS/Peak) over a defined frequency range (e.g., 10 Hz to 1 kHz). |
| Sensitivity | Special "X1" Value (e.g., 500 mV/in/s or 20 mV/mm/s). | A key parameter defined by the "X1" code. Differs from standard 100 mV/in/s or 1000 mV/in/s sensors. |
| Frequency Range | Typically 4.5 Hz to 1 kHz (for velocity). | Optimized for monitoring casing vibration of common rotating machinery where the fundamental frequency is above 10 Hz. |
| Mounting Interface | ¼-28 UNF threaded stud (Common) or M10x1.0 metric thread. | The "X1" configuration likely specifies this. The kit includes a matching stud for permanent installation. |
| Housing Material | Stainless Steel (316L) or Nickel-plated alloy. | For corrosion resistance in outdoor or chemical environments. |
| Connection | Integral armored cable with a connector (e.g., 3-pin MIL-C-5015) or a terminal box. | The cable is part of the "149032-08" assembly. Length is specified by the kit (e.g., 10m). |
| Cable Jacket | Heavy-duty PUR (Polyurethane) or FEP Teflon®. | Oil, chemical, and abrasion resistant. Suitable for tray routing. |
| Operating Temperature | -50°C to +120°C (Extended range likely for "X1"). | |
| Weight (Transducer Only) | Approx. 300 - 600 grams. | Substantial due to robust metal housing. |
| Weight (Complete Kit) | Approx. 1.5 - 3.0 kg. | Includes transducer, cable, mounting hardware, and packaging. |
| Dimensions (Transducer) | Diameter: ~ 25-35 mm Height: ~ 60-80 mm. | Compact cylindrical design. |
| Power Requirement | Passive (Two-wire) for velocity sensors, or ICP®/IEPE (Two-wire with constant current excitation) for accelerometers. | The "X1" code defines the electronics type. Most modern versions are ICP®. |
| Key Feature | Complete, Ready-to-Install Kit. The "-08" kit ensures all correct mating hardware is provided, eliminating field sourcing errors and guaranteeing proper mechanical grounding and sealing. | |
| Calibration | Individually calibrated and shipped with a calibration certificate. | Critical for accurate measurements. The "X1" sensitivity is verified. |
Primary Application Scenarios
This complete kit is used for permanent installation on machinery where casing vibration is a key health indicator.
Steam & Gas Turbine Bearing Casing Monitoring:
Mounted vertically on the bearing housings to monitor absolute casing vibration. This data complements shaft relative vibration (from proximity probes) to provide a full picture of machine dynamics and detect structural issues or foundation problems.
Large Centrifugal Compressors & Pumps:
Installed on the casing of critical process compressors and high-energy pumps in refineries and chemical plants. Used for predictive maintenance to detect imbalance, misalignment, bearing defects, and flow-induced vibrations (e.g., surge, cavitation).
Power Generation Auxiliary Equipment:
Induced Draft (ID) & Forced Draft (FD) Fans, Boiler Feed Pumps: Monitoring these large motors and fans for developing mechanical faults, preventing unplanned outages.
Paper Mill & Steel Mill Rolling Equipment:
Monitoring large gearboxes, rolls, and motors where high loads and hostile environments (moisture, heat) demand a robust, pre-packaged sensor solution.
Condition-Based Maintenance (CBM) Programs:
As part of a plant-wide CBM system, these kits are used to standardize and simplify the installation of vibration points on hundreds of assets, ensuring data consistency and reliability.
Global direct procurement guarantee
All products are purchased directly from overseas original manufacturers or authorized channels, 100% guaranteed genuine quality, sufficient spot inventory, and comprehensive model coverage
Quality Commitment
Each product has been tested by our technicians, providing 12-month long warranty, worry-free after-sales
Flexible procurement plan
- Bulk order enjoys Friendship discount (2 pieces or more can be applied)
- Long-term cooperative customers can apply for priority supply
Full service support
7×24 hours technical consultation, from selection guidance to installation and commissioning to provide full life cycle service (paid)
Why do so many customers choose us?
On the basis of the same quality, we provide:
- More competitive price system
- Faster logistics response
- More complete technical support (free product technical documentation)
Your trust is the driving force for our continuous progress, submit your requirements immediately to get exclusive quotes
