Introduction
The Bently Nevada 9200-01-05-10-00 is a specific model of a 4-20 mA Vibration Transmitter from the GE Bently Nevada 9200 series. This device is designed for continuous, single-channel monitoring of overall vibration velocity (in units like in/sec or mm/sec) on general-purpose industrial machinery such as pumps, motors, fans, and compressors.
Unlike the more complex 3500 system modules used for critical protection, the 9200 transmitter serves as a simpler, cost-effective solution for condition monitoring. It integrates an internal seismic sensor (for casing vibration) and signal conditioning electronics into a single, rugged package. It converts the measured vibration level directly into a standard 4-20 mA analog output signal, which can be easily wired to and interpreted by a plant's Distributed Control System (DCS), Programmable Logic Controller (PLC), or a basic indicator. This allows for continuous trending and alarm generation based on machinery health.
Parameters / Specifications
The key technical specifications for the Bently Nevada 9200-01-05-10-00 are summarized in the table below.
| Parameter | Specification |
|---|---|
| Part Number | 9200-01-05-10-00 |
| Product Line / Type | Bently Nevada 9200 Series Vibration Transmitter |
| Measured Parameter | Overall Vibration Velocity (Casing Vibration) |
| Output Signal | 4-20 mA two-wire, loop-powered (The -01 suffix typically specifies this 4-20 mA output). |
| Measuring Range | 0-1.0 in/sec True Peak (0-25.4 mm/s) (The -05 suffix often corresponds to this range). |
| Frequency Range | 4.5 Hz to 1000 Hz (270 CPM to 60,000 CPM) |
| Power Supply | 12 to 30 V DC (loop-powered) |
| Electrical Connection | 1/2" NPT Conduit connection (The -10 suffix typically specifies this connection type). |
| Mounting | Single 1/4-28 UNF threaded stud (on base) |
| Housing Material | Stainless Steel |
| Sensing Orientation | Any (omnidirectional) |
| Dimensions (Approx.) | Diameter: 2.5 in (64 mm), Height: 3.5 in (89 mm) |
| Weight (Approx.) | 1.5 lbs (0.68 kg) |
| Operating Temperature | -40°C to +85°C (-40°F to +185°F) |
Note: Suffix interpretations are based on common 9200 series configuration codes. For absolute certainty, consulting the official Bently Nevada 9200 datasheet is recommended.
Application Scenarios
The 9200 Vibration Transmitter is designed for widespread use on general-purpose machinery where continuous, reliable vibration monitoring is needed for predictive maintenance, but the full complexity of a protection system like the 3500 is not required.
Typical application scenarios include:
Critical Pump and Motor Monitoring:
Permanently installed on cooling water pumps, charge pumps, and large electric motors in industrial plants to provide early warning of bearing wear, imbalance, or misalignment, allowing maintenance to be planned before failure.
Fan and Blower Monitoring:
Mounted on the bearing housings of induced draft (ID) fans, forced draft (FD) fans, and industrial blowers to monitor for vibration caused by fouling, imbalance, or structural issues.
OEM Machinery Integration:
Built into original equipment by machinery manufacturers to provide a built-in vibration monitoring capability, making it easier for end-users to integrate the machine's health into their plant control system.
Basic Compressor Monitoring:
Used on non-critical or smaller compressors to track overall vibration levels and provide a 4-20 mA signal to the central control room for operational awareness and alarm generation.
Industries of Use:
Water and Wastewater Treatment
Chemical Processing
HVAC and Power Generation (for auxiliary equipment)
Manufacturing and Industrial Plants
Pulp and Paper
Global direct procurement guarantee
All products are purchased directly from overseas original manufacturers or authorized channels, 100% guaranteed genuine quality, sufficient spot inventory, and comprehensive model coverage
Quality Commitment
Each product has been tested by our technicians, providing 12-month long warranty, worry-free after-sales
Flexible procurement plan
- Bulk order enjoys Friendship discount (2 pieces or more can be applied)
- Long-term cooperative customers can apply for priority supply
Full service support
7×24 hours technical consultation, from selection guidance to installation and commissioning to provide full life cycle service (paid)
Why do so many customers choose us?
On the basis of the same quality, we provide:
- More competitive price system
- Faster logistics response
- More complete technical support (free product technical documentation)
Your trust is the driving force for our continuous progress, submit your requirements immediately to get exclusive quotes
